AD-8000 Operating Manual
Page 32
ANALOG AND A/D CONVERTER
Parameter Value Units
Resolution 24 bits
Sample Rate 32–54 kHz
Input Impedance
Pro 9K Ω
Consumer 15K Ω
Relative THD+N
–0.1 dBFS –108 dB
–110.5 dB (A-weighted)
–20 dBFS –88 dB
–91 dB (A-weighted)
–60 dBFS –52 dB
–54 dB (A-weighted)
Dynamic range
–60 dB 112 dB
–60 dB, A-weighted 114 dB
Peak Spurious Component –120 dB (Max)
Group Delay (in passband) 38.7/Fs seconds
Passband Ripple ±0.001 dB
Digital Filter Stopband 26.232 kHz
Stop-band Attenuation 110 dB
Channel Separation
Left/right 113 dB (Worst Case)
Between pairs 113 dB (Worst Case)
Frequency Response (20 Hz–20 kHz)
Gain ±0.025 dB
Phase <2 Degrees
Common-Mode Rejection Ratio
60 Hz > 100 dB
1 kHz > 80 dB
Input Level, Maximum (No Gain)
Professional, balanced 27 dBu
Professional, unbalanced 23 dBu
Consumer, balanced 16 dBu
Consumer, unbalanced 15 dBu
Input Level, Adjustment Range 20 dBu
Crystal Oscillator Accuracy ±25 ppm
Clock Jitter, 32kHz–54 kHz << 50 psec
Note: These specifications are
subject to change without notice.
HEADPHONE D/A AND AMPLIFIER
Resolution 18 bits
Sample Rate 32–54 kHz
Relative THD+N, S/(N+D)
–0.5 dBFS input –88 dB
Dynamic range
–60 dB –94.6 dB
–60 dB, A-weighted (EIAJ), typ –96 dB
Group Delay (in passband) 22.25/Fs sec
Passband Ripple ±0.17 dB
Stop-Band Attenuation 35 dB
Channel Separation
DAC 97 dB
Amplifier 65 dB
Frequency Response (20Hz–20 kHz)
Gain ±0.05 dB
Phase < 2.5 degrees
Output Level (max) 8 Vp-p
Output Power (max)
8 Ω load 1 W/channel
150 Ω load 50 mW/channel
600 Ω load 20 mW/channel
DIGITAL SIGNAL PROCESSOR
Processing Delay 16/Fs Seconds
DC High-Pass Filter Corner Freq. 1.0 Hz
UV22 Amplitude
Normal, 16 bits –84 dB
Low, 16 bits –90 dB
Normal, 20 bits –108 dB
Low, 20 bits –114 dB
Metering
Accuracy ± 0.05 dB
Over Detection 1–4 consecutive
0 dBFS readings
(User-definable)
SYSTEM
AC line voltage 100, 120, 220, 240 vac
(set internally)
Fusing 1 A slow-blow U.S.A.
Power 60 Watts
Size (w, h, d) 19 in, 3.5 in (2U), 14.25 in
Weight 20 lb (9.1 kg)
Appendix IV: AD-8000 Specifications
Public Revision History
Version 1.0, July 24, 1997 – Initial release version: for distribution.
Version 1.1, August 29, 1997 – Reference to DIP switch corrected on p11 (“Connections”). Minor revisions to
diagram on p31 (NTSC generator with DA-88). Release version for distribution.
Version 1.2b, October 7, 1997 – Corrections to reflect firmware revisions 0.55-1.02. Discussion of Autosync and
power-up version display added.
Version 1.3, December 1997 – Corrections and additions to reflect firmware revisions to 1.15. Changes from
previous firmware revisions is available on the Apogee Web Site.
Version 1.4, November 1998 – Corrections and additions to meet CE requirements. Some additional informa-
tion included.
Comments to this Manuals